Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel to it thanks to its bigger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models may be a bit spongy at times. The front tyres in the Qashqai may also lose traction on rough surfaces, and the CVT could occasionally display wrist-flexing torque steering.

It is usually caused by an inoperable coin battery, which is easily replaced in just a few minutes. Make sure that the replacement battery is of the same voltage, size and specifications.

Water Damage

One of the most common reasons a Nissan key fob might display the "key ID incorrect" message is due to water damage. The key fob comes with rubber seals which protect the chip inside, however prolonged exposure to moisture can cause it to stop working properly. This is typically the case if you've dropped your key fob into the ocean or a pool pool, but it can also happen if it gets wet from soapy hands or rain.

If your key fob has been exposed to water for an extended period of time, you may need to clean it using isopropyl and electronic cleaner. It may also need to be taken to a professional to be repaired or replaced.

If your key fob does need to be replaced the process is simple. First, make sure that you have a multipack of the right battery (CR2032 3V). The front and rear cases with the flat-head screwdriver. Remove the metal clips, then remove the old battery and replace it. Reassemble the fob and replace the mechanical key. Verify that it is working properly. If not it, you'll need to bring it to a Nissan dealer or a professional auto locksmith for the replacement of the chip in the key. Fortunately, the chip is not usually damaged by water exposure which means that this shouldn't be a major expense.

Dead Coin Battery

Another common reason your Nissan Qashqai key fob might not function is that the battery for the coin is dead. The batteries typically last for 3-5 years, but they may fail in time, particularly if the fob is dropped frequently. You can replace the battery, but make sure it is the same voltage and the same size as the previous. If you choose to use a different battery, it can cause the key to have an incorrect key ID which can prevent it from paired with your vehicle.

The best way to replace the battery on a Nissan Qashqai key fob is by removing the key fob using a small flat head screwdriver. The screwdriver should be put into a small hole on the bottom of your key fob. The screwdriver should be gently twisted to divide the two halves. Remove the old CR2025 battery and replace it with a new one, noting the position of the old one in the fob.

Before putting the new battery in be sure that there is no dirt or water damage to the terminals. If so, clean the terminals using some isopropyl ethanol. Make sure that the pole cables are properly connected. They should be connected both the positive and negative poles of your battery.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water it could be a sign of an internal chip issue. You'll require a new keyfob if you can't fix the problem by replacing the battery. If the key fob stopped working after dropping it, it is likely that the chip inside was damaged. If you clean the chip with isopropylethanol and [Redirect-302] paper towels and then insert it into the key fob, you will generally get it working.

A common error that you might see on the dashboard of your car is "Key ID Not Correct." The vehicle is unable recognize the key fob and therefore will not allow the car to start. The issue could be caused by a variety of factors, including water damage, undetectable problems in the key fob's circuitry or RFID interference.

If the 12 volt battery in your key fob dead or not providing sufficient electric current it will cease to function. This could affect your Nissan Qashqai's remote keyless system central locking, as well as the ability to start the engine with the key fob. If you can't lock or unlock the door manually, you should check the batteries on your key fob and make sure they are in good shape. You can also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged into saltwater the device should be able to be revived with a simple rinse of clean water. You might also try cleaning your electronic chip with isopropyl alcohol or an electronic cleaner. If none of these methods work it is possible to replace the key fob.

If your Nissan Intelligent Key still does not work, there might be a problem connecting between it and your vehicle. To reconnect it, start by turning the key in the ignition, but not starting the car. Keep doing this until you see the hazards lights flash twice. Turn off the vehicle and take off the key.

Open the fob compartment in your vehicle. It's usually located in a door jamb on the handle on the driver's side or under an armrest. Locate the small button labeled "program" and press it. You should hear a chime sound after the process has been completed.

It's time to test your Intelligent Key to the test. Make sure you press all the buttons on the key while standing at a distance away from the car. If the lights flash or the horn sounds, then the key is connected to the nissan key fob replacement. You may also try testing it in close proximity.