Replace Nissan Key Fob Batteries

If your Nissan keyfob isn't responding to your commands, its battery could be dead. This is a repair that most people can do themselves.

You can find the replacement from a local hardware store or from your owner's manual for the particular model you have You'll need follow these steps to replace the battery.

Removing the Battery

The key fob in your Nissan model is fitted with an inbuilt lithium battery which will eventually lose charge. Luckily, changing the battery in the key fob is an easy process that only takes less than a few minutes. First, you'll need an CR2032 battery. It's a tiny coin cell battery that's often found in key fobs, and is available at all convenience stores. You'll also require gloves (latex or non-latex) and a small flathead screwdriver to open the fob. Read the owner's manual for specific instructions and steps before starting.

Flip the fob upside down and look at the backside. You will notice a small latch that you need to release by pulling down. This will release the mechanical key from its initial position inside the fob.

Install the new battery and make sure that it's properly positioned. Close the fob after the battery is in place and then press the two sides of the fob together. After you've completed this last step check your key fob by pressing the unlock button and watching what happens. If everything is in good condition, you're able to enjoy the Nissan's features. It's recommended to program the key fob after replacing the battery to ensure it's working properly.

Replacing the Transmitter

Your key fob is the "key" for the majority of your vehicle's essential functions. It could be a devastating blow in the event that it's damaged or lost. A damaged or broken key fob will prevent you from locking and starting your vehicle.

Therefore, it's a smart idea to keep an extra key fob on hand in case of an emergency. Luckily, the process of replacing your Nissan key fob is relatively straightforward. You'll require a new battery and a small flathead screwdriver to remove the old one, but the replacement key for nissan micra process is easy and will only take about a couple of minutes.

You'll require an oval Panasonic CR 2032 3V battery (you can typically find them in multipacks for under $5 USD). The battery is situated in the back of the key fob. You'll require a small flathead screwdriver in order to gently separate the two halves. Utilize a small flathead screwdriver to push the clip on top of the battery to pop it out, Replace nissan Key fob taking note of its position. Replace the battery, and assemble the key fob. Make sure to test it to verify it is working.

As with any electronic device that you own, Replace nissan key fob like all electronic devices, your Nissan Intelligent Key will eventually wear out over time due to normal use and will require replaced. Guard your key fob from magnetic fields, water, and physical impacts. Do not drop it or put too much pressure on the device.

Replace the Key

If your Nissan key fob dies and you are unable to use it to unlock your car or even start it. That's a problem for people who need to get to work in Detroit or run errands in Dearborn, or enjoy some night out close to Troy.

The good news is that the battery in your Nissan smart key isn't too difficult to replace. You can replace the battery at home, or at the dealership. A pack usually costs $5 or less.

Flip the fob over and push the small catch to the back. This will release the emergency mechanical keys inside. The emergency key will not allow you to start your car however, it will allow you to open the door.

Next look for a tiny opening on the top of the casing for the key fob. These are great to put screws into, allowing you to pry the two pieces of the key fob. Once you've reached the internal battery, remove it and take note of its location. When you are in a position to reassemble your key fob, slide in the new battery and then snap the two components of the case back together. Then you can insert the mechanical key and your Nissan smart key will operate as usual.

Other Issues

Many modern vehicles come with key fobs, which allow you to lock them and start them without the need for a physical key. Key fobs use the transmitter to communicate with the computer system in the car.

If your Nissan key fob stops working after changing the battery, there could be many reasons to blame. One possibility is that the new battery wasn't properly fitted into the key fob. A reset of the key fob is also a possibility. Fortunately, this is an easy task that can be accomplished at home with some simple tools.

You'll need, for instance an screwdriver with an angled tip to remove the old battery from the key fob. Then, you can use an open-ended screwdriver the back of the key fob and insert the new battery. In the end, you'll have to reprogramme the key fob so that it is compatible with your vehicle.

Fortunately, most Nissan key fobs are programmed by the user and you can do it yourself. This is usually done by inserting the keyfob into the ignition two times within five seconds. If this does not work, take your key fob into a dealer or an auto locksmith to have it programmed. The cost of this will differ based on the person you talk to and the kind of car you own.