Replace Nissan Key Fob Batteries

If your Nissan key fob isn't responding your instructions, it's most likely that its battery is dead. It's a relatively easy repair that most people can do themselves.

You can get an alternative from a hardware store or your owner's manual for the specific model you own and then follow these steps for changing the battery.

Removing the Battery

The key fob in your nissan car key replacement model has a built-in battery that will eventually lose its charge. The key fob's battery can be changed in just a few minutes. First, you'll need to purchase an CR2032 battery. It's a tiny coin-cell battery that is used in most key fobs. You can find it in most convenience stores. You will also need gloves (latex or non-latex) and a small screwdriver with a flat head to open the fob. Check the owner's manual for a detailed guideline and steps to follow before you begin.

Turn the fob upside down and look at the backside. You will see a small catch that must be released by pulling it down. This will release the mechanical key from its initial position inside the fob.

Install the new battery and ensure that it is properly aligned. Close the fob once the battery has been installed and click the two sides of the fob together. After you have completed this step verify your key fob by pressing the unlock button and observing what happens. It's now possible to use the many functions of your Nissan If everything is working properly. It's also a good idea to re-program your key fob after replacing the battery to ensure it's functioning correctly.

Replace the Transmitter

Your key fob is the "key" for the majority of your vehicle's important functions. It could be a big blow when it is damaged or lost. A damaged or dead key fob can prevent you from locking and starting your vehicle.

Therefore, it's a smart idea to have an extra key fob in your possession in the event of an emergency. Fortunately, the process for replacing your Nissan key fob is straightforward. The procedure for replacing your Nissan key fob is fairly easy. You'll need a new flathead screwdriver, as well as a new battery to remove the old.

You'll also need a Panasonic CR2032 3V round battery (you can find them in multipacks, which cost under $5 USD). The battery will be inside the key fob's back half and you'll need gently turn the two halves in order to expose it. Utilize a small screwdriver to lever the clip on top of the battery and lift it out, making a note of its position. Replace the battery and put the key fob back together. Test it to make sure it works properly.

As with all electronic devices, like any other electronic device, your Nissan Intelligent Key will eventually wear out due to regular use and will need to be replaced. Protect your key fob against magnetic fields, water, and physical impacts. Be careful not to drop it or put too much pressure on the device.

Replacing the Key

If your Nissan key fob is no longer working the fob isn't able to unlock or start your car. This is a major issue for those who need to go to work in Detroit or do errands in Dearborn.

It's not difficult to change the battery in your Nissan Smart Key. You can replace the battery at home, or at the dealership. The cost of a replacement pack is usually less than $5.

Start by flipping the fob over and then pushing a small catch on the back. This will open the emergency mechanical key inside. The emergency key will not allow you to start your car however it will open the door.

Find a small cut at the top of the casing. You can use a screwdriver for prying off the two pieces of the key fob. Once you've got access to the battery inside, take it out and make note of the position it is in. When you are in a position to reassemble your key fobs, insert the new battery and snap the two parts of the case back together. Then insert the mechanical key and your Nissan smart key will operate as usual.

Other Problems

Many modern cars are equipped with key fobs that allow you to lock and open them without the need for the physical car key. The key fob works as an electronic transmitter to connect with the computer system in the car.

If your Nissan key fob doesn't work after you change the battery it could be due to several reasons for this. One possibility is that the new battery was not correctly placed into the key fob. Another possibility is that the key fob needs to be reset. Luckily, this is an easy process that can be accomplished at home using a few simple tools.

For instance, you'll need an appropriate screwdriver, Nissan key fob with preferably with a flat head to unlock the key fob to remove the battery that was in there. With a screwdriver, break the back of the keyfob and then insert the new batteries. You'll also have to reprogramme your key fob to allow it to function with your vehicle.

You can easily program your Nissan key fob by yourself, since they can all be programmed by a user. This is usually accomplished by inserting the keyfob in the ignition twice within five seconds. If this does not work it is possible to take your key fob in to a dealer or auto locksmith to have it programmed. The cost of this will vary depending on who you contact and the type of vehicle you own.