How to Fix a Dead Kia Picanto Key Fob

The Kia Picanto was built for the city. It swerves through traffic gaps that bigger cars can't and can wiggle through width restrictions as if they're not there at all. It's a small car with lots of features.

There are a variety of reasons why the key fob on your kia soul key replacement Picanto may not work. A dead battery is the most typical cause.

Dead Coin Battery

A battery that is dead is the most common cause of a Kia venga replacement Key Picanto's keys fob not working. The key fob will typically show warning signs like unpredictable behavior or loss of range before it goes out of service. It is recommended to replace your battery in the event that you observe any of these symptoms before the battery completely fails. Make sure you choose an alternative battery that has the same size, voltage and specification as your original one.

If the fob for your key is not working, you may be required to take it to an authorized dealer. Only then can you be certain that the replacement key fob is compatible with your vehicle and will be programmed correctly. The process of reprogramming a key fob without the correct procedure could damage the chip inside and cause it to stop working.

Another possibility is that the receiver module has developed an issue. This could be due to damaged chips or wear and tear over time. It can be difficult to identify the signs of this issue, but it is important to look into the issue whenever you can. If your key fob isn't working, or the spare is not working and you are unable to use it, contact an auto dealership for assistance. They can help you identify the problem and fix it.

Faulty Chip

The key fob is equipped with an internal chip that transmits an electronic signal to the car's computer. If the chip becomes damaged, it will not transmit the correct code and the immobilizer feature of the car will be activated. This can happen due many reasons. One reason could be low battery levels in the key fob. Water damage is another possibility. If the fob gets wet, it's likely that it will stop working.

A faulty chip can also be the cause of a Picanto key fob not turning on the engine. If you've replaced the battery, reprogrammed it and then inserted the fob but it still doesn't function, the circuit board could be damaged. You'll need to replace the circuit board if this is the situation.

To open the Fob you will need to press on the button on the back of the fob. Once this is done, you'll be able to remove the mechanical key. The video below will guide you how to replace the battery inside the key fob. Make sure you use a battery that has the same dimensions and voltage. The Fob may be damaged if using the wrong type of battery. After replacing the battery you should check it by pressing the lock button. If it works then you've got a fantastic Fob.

Faulty Receiver Module

Your key fob isn't indestructible and takes a lot abuse. In time, its contacts with batteries and buttons may be damaged and stop functioning properly. Fortunately, it's relatively easy to repair this yourself using a few simple tools.

To function, the fob must send a signal through a receiver inside your car. If this module is damaged it will not be able open or start your vehicle. There are a variety of possibilities for the cause of this issue however the first thing to try is resetting the fob.

This is usually done by disconnecting the 12 volt battery from the fob and letting it drain completely. Then, reconnect the positive and negative cables in reverse order.

If the battery is good and the fob is free of water damage, it could simply have an issue with its signal. This could be due to many things like interference from nearby transmitters, or [empty] objects that use the same frequency band as the Picanto's receiver.

Key fobs are constructed with rubber seals that prevent the chip inside from getting wet. However, if they are submerged for prolonged periods the chips may be destroyed. It's essential to keep your key fob free of water and only use key fobs with waterproof designs.

Programming errors

A Kia Picanto key fob is an ideal way to open and start your car. You can also use the key fob in order to control your vehicle. It is important to know how to use the key fob properly especially when driving in bad weather or if you are unable to move. Fortunately, [empty] there are plenty of Kia Picanto key fob tips to help you out with this!

If your key fob stops working out of the blue it could be an issue with its internal chip. This is a rare occurrence however it could happen. It is best to consult a Kia dealer to pinpoint the issue.

Alternatively, you can try to reset your Picanto key fob. The procedure is quite simple and can be completed at home. The first step is to remove the key fob from the ignition switch. Connect the diagnostic device under the dashboard to the OBDII connector and start the engine. The diagnostic tool will ask for details about the Picanto. This includes the make and model as well as the VIN.

You can also look for a dead battery. The metal retaining clips that are inside the key fob are designed to hold the battery in place and complete the circuit. If the retaining clips are loose, they can cause disruption to the flow of electrical energy and cause a loss of function.