how to fix kia key fob to Replace a Kia Sportage Replacement Key

For a variety of Kia models the key comes with a built-in keyless entry system. This key typically resembles an electronic remote and can be changed with a brand new one from a Kia dealer or locksmith.

Key fobs might stop working due to various reasons, such as batteries that are dead worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some suggestions on how to get your kia picanto key fob Replacement Sportage replacement key working again.

How to replace a remote key or a smartkey?

Whether your Kia is equipped with an intelligent key, [Redirect-302] remote key push to start key or a regular non-transponder metal key, the battery in these keys will eventually require replacement. This is especially relevant if your car displays a message that the smart key or remote has low battery power.

It's a simple process. To replace the battery of the keyfob remove the mechanical key from the slot at the back of the fob. Then, pull the cover off. Inside the key fob will be the small screw that holds the battery in the correct position. By using a small screwdriver remove the screw and remove the battery that was in place. Install the new battery and then close the gap on the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the lock and unlock buttons. If the doors lock and unlock in the same way, you're all set! You can now use the hands-free lock/unlock feature on your Kia when your fingers start to get cold or you have to run some errands in Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're required to reprogramme your key, it is necessary to write down the key code's number on the key code tag.

How to replace the battery

If the Kia key fob does not respond to pressing the lock or unlock button, it's a sign that the battery is depleted. A low battery could cause other issues such as the check engine light turning on or [Redirect Only] delayed engine cranking. Fortunately replacing the key fob battery is a relatively easy DIY project that requires only some basic tools.

Make sure that you shut off your vehicle and shut all doors prior to beginning. Find the small metal or a plastic piece near the bottom of the key fob. Jiggle it until the metal key comes out. Then, you can put the key into the handle on the door of your driver to unlock your car.

To replace the battery in the key fob, take off the cover that covers the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and orient the new battery to ensure that the "+" positive side faces you, and the "-" negative side is facing the fob's electronic contacts. Avoid using too much force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.

After installing the new battery then turn the key fob on and off in the ignition until the door locks up. You can then test the Kia's Key fob once more to ensure it's functioning properly.

How to replace the smart key?

You can have a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference is that the smart key comes with a small mechanical key blade in it, whereas the standard fob does not. Both types of key fobs have an internal battery that eventually will need to be replaced. This is an easy process which takes just two minutes.

Make sure to shut off your Kia and stand on a level, well-lit surface before you begin. Remember that the fob contains tiny parts that could be thrown off when you're not careful.

The first step is to find the small release button that is located on the backside of the fob. It will be a circular button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the old battery. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. Once you're done you should be able to lock, unlock and start your vehicle using your key fob, even if the engine isn't running!

How do you replace a mechanical key

The Kia keyfob is a great convenience, allowing us to lock or unlock our car with just pressing the button. But, as with all devices there are issues with it at times. There are ways to address these issues and keep your key fobs in good working order for the duration of.

One of the most frequent problems is a weak or dead battery. This can cause the fob to stop working entirely or even to stop working intermittently. If this is the case you should replace the battery with a fresh new one.

If this doesn't resolve the issue Try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed, replace it with a brand new battery.

When the new battery is in, close and then open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the key fob to confirm it's functioning correctly. If the fob still not working, contact an authorized locksmith or dealer to resolve the issue. To avoid lockouts in the future, ensure you have an emergency key that can work on all door and trunk cylinders.