Citroen Berlingo Key Fob Troubleshooting

Citroen's Berlingo Multispace occupies a utilitarian market in the people-carrier market. Its sliding doors at the rear allow it to be squeezed into parking bays and its sturdy cabin is more robust than many of the more expensive rivals.

However, if your device has been bathed in soapy or salt water, it might not function properly again - even after a fresh battery and programming. This is because the internal chip has been damaged due to exposure to water.

Water Damage

Shake your key fob to remove as much water as you can. Place it on the ground with the button in the downward position, and let it drain for a few minutes while you wipe down the inside using a soft cloth. This will stop any condensation from causing damage to the electronic chip.

If your Mk 2 Citroen Berlingo or Mk 3 Citroen Berlingo dashboard warning light, which appears like a car key symbol, lights up, it could be a fault with the immobilizer. It is a security device within the vehicle to deter thieves from hotwiring it. If this is the case you'll be required to visit an Citroen dealer or a certified mechanic to solve the issue.

A constant engine warning light may indicate that the electric power assisted steering is not working properly. If this is the situation it is recommended to stop the vehicle and check the temperature and pressure of the oil before restarting it. If the issue persists, you'll have to visit a citroen c4 key dealership or a trained mechanic in order to resolve the problem.

Dead Battery

A dead battery in the coin is the most frequent reason for your key fob not to function in your Berlingo. The button cell battery inside the key is very simple to replace, however you must ensure that you use the correct voltage size and Verlene Blakeley type of battery. An uncompatible battery could damage the circuit board. A dead coin-cell battery could also disable the anti-theft feature. This is a safety measure that stops the engine from being started without an actual key.

If the key fob doesn't respond to the lock button even after replacing the battery, it could be that the receiver module is faulty and is not communicating with other modules in your vehicle. This can be confirmed using an OBDII scan tool.

If the key fob still not responding, Kendall Beardsmore try reprogramming it. Follow the directions in your owner's manual for this procedure. Once the device has been reprogrammed, the device should be working perfectly.

Troubleshooting

Citroen Berlingo owners are generally pleased with the reliability of the car. However, like any vehicle there are a few issues that do occur. One of the most common is a dead key fob battery. Fortunately, it is simple to determine and can be repaired in just a few minutes. Other issues that could arise are a worn button or a water damage to the electronic chip, signal interference or a remote keyless system receiver module that has developed an issue.

It is vital to be aware that not all keyfob batteries are same. Certain batteries are made from inferior materials and could damage your remote key fob or other electronics in your vehicle. When replacing the battery, you should make sure you use a battery of the same type and voltage as the original. Make sure that the new battery is properly fitted. Ensure the positive (+) side of the battery faces upwards when inserted into battery slot.

If you notice an indicator light on your car's dashboard which appears like a triangle with an exclamation point, this signifies that the vehicle has identified problems with its electric power-assisted steering. If the warning light illuminates while driving, it is advised that you seek advice from a trained mechanic or Citroen Berlingo (incl Multispace) dealership.

Radio Interference

Radio interference could be the reason that your key fob isn't functioning at all. This is a common problem caused by devices that use the same frequency as your remote control. Certain wireless security systems, for instance LED lights that are sold aftermarket, may interfere with the RF signal. Try moving these devices into an alternative location if you've got them in your home.

In addition to devices that operate on the same frequency, there are also environmental factors that could interfere with a car's key fob. Metal objects, for instance could interfere with the strength of the signal. Rainy weather may also bend the antenna of the fob, which results in a weaker radio signal. In some cases, even when the fob is near to the car it may not respond to radio signals.

Check the battery to ensure the health of your key fob. The battery should be in good working order and the contacts must not be damaged by corrosion. Contacts that are damaged by corrosion are one of the main reasons for key fobs not responding to the vehicle's radio signals. A depleted battery could cause the fob to malfunction. If the issue persists after replacing the battery, the antenna may be faulty. Locksmiths can check the keyfob and fix it.