Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths with the right tools and know-how. They will be able to make and program new keys much faster than a dealership would and at a lesser cost.

A dead coin battery is most likely to be the cause the reason your key-fob stops locking or unlocking doors. There are also other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and cannot start the engine. In this situation you'll need to choose the alternate method to start that is described in the owner's manual.

Another reason your 208 may not start is because the spark plugs have worn down. The spark plugs ignite fuel to start the engine. However, they have a limited life span. If they aren't used enough, they will eventually fail.

There is a simple solution for this issue. The best thing to do is to measure the voltage of your car battery with a multimeter. If it is below 11.5 volts it is time to replace it. It is also necessary to clean the battery's contacts when it has corrosion. This can be done by removing the rubber covers from the two battery terminals and then using a wirebrush to remove any parts of the battery that are corroded. Then, reconnect the cables to the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery has not gone flat, you should look at the spark plugs. It could be that they are just overly dirty, causing them to not to spark. This can be fixed by cleaning the spark plugs in the workshop.

Peugeot automobiles use a key with a transponder that is compatible with the immobiliser. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

This is a common problem that is caused by water damage. This is particularly prevalent in colder climates, as the vehicle may have been exposed to snow or rain. If this is the case, you should get in touch with a reputable locksmith who will have all of the tools and equipment required to reprogram the new key. They will also have the latest technology and machinery needed to make a Peugeot smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the carbon-encased transponder chips to a new kind of chip that utilizes electronic components that are placed on circuit boards. This new technology works great when it's fresh, however, over time, the circuit boards begin to lose their effectiveness and cease working properly.

This could stop the immobiliser chip from activating the immobiliser chip, causing your car not to start. Contact an Peugeot specialist, Peugeot 208 Key Replacement or a locksmith if this is the situation.

A common issue is when the battery in the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, this is normally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty If your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden rainstorm or accidentally washed. The receiver is responsible for transmitting radio frequency signals to an on-board computer that controls the central locking system within your peugeot boxer key vehicle.

Rubber seals on the key fob prevent water from getting to the electronic chip. However, prolonged exposure to water could penetrate these seals and damage the chip. Submerging the key fob into ocean water at the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working, you'll need to have the module replaced. This can only by done by a Peugeot specialist or an expert auto locksmith. As opposed to other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the correct coding in order to start the engine. It is for this reason that you should only trust the peugeot 3008 key fob locksmith to create and program an alternative.

Computers with faulty on-board computers

The on-board computer inside your Peugeot is responsible for many of the systems within your car, from airbags to power windows. If something is wrong with these systems, it'll typically display a code that identifies the issue. This code is saved in the system and will stay there until the issue is solved. This may require the on-board computers to be replaced.

The most frequent cause for the warning light for airbags to flash is corrosion or loose connections within the sensor. This could be due to wear and tear, aging or exposure to salt and moisture. It is crucial to get this issue addressed as soon as you can, since the airbag malfunctioning could be risky in the event of an accident.

If your Peugeot is showing a card that is not being detected error then the key battery in the key fob might be weak or dead. This prevents the key fob from sending a signal that disarms your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this fails it is because the battery of the key has to be replaced.