Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are long-lasting, durable and easy to maintain. As opposed to aluminium and timber they do not get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will help prevent unnecessary repair costs and also increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is important to ensure that your windows are in good condition.

For single pane windows it is fairly easy to replace windows, and the new one is usually able to fit into the old frame very easily. However, if you have double-pane windows that are secured by internal beading it will be more difficult to remove the old panes and put in new ones. In this instance you'll need locate some plastic spacers that will assist the new pane to fit properly into the window frame.

If you are going to try to remove the glass panes yourself it is crucial to wear the appropriate safety equipment such as gloves that are thick and eye protection. It is also recommended to lay down a dropcloth before you start working on the glass, so that any shards fall onto the fabric rather than on the floor, where they could be trampled on and cause further damage.

It's a great idea to cover the gap with tape after the glass has been removed. This will keep drafts and water from entering your property until a professional is able to repair the window. It also acts as an obstruction to prevent intruders from getting into your home. If the gap between the door and the window is large, you might need to consider an alarm system that has a window. This will provide the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. In time, they could develop a variety of issues such as sagging. A sagging window can cause problems with light, draughts and even security. It's important to take action when you notice your uPVC windows are falling down.

To fix a sagging window you can try to reposition the hinges. To accomplish this, you'll have to open the window to access the frame. Then, using the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and check for an appropriate fit. If you're satisfied with the fit, tighten the screws until they remain in position.

If you can't reposition the hinges you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, causing them to loosen. If this happens, it's important to replace the seal as soon as possible to ensure your uPVC windows remain watertight and secure from draughts.

uPVC handles may also loosen. This is often caused by screws that have become undone over time, but it could also be due to the handle mechanism wearing out. It's a good thing that it's simple to fix a loose uPVC window handle yourself. First, you'll need to shut the window and perform an initial fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it doesn't, you can use a screwdriver to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains it's crucial to take action. Water leaks through windows can cause structural damage to your home and hinder your ability to control the temperature of your home. The most common reason for leaking uPVC windows is that the sealant around the frame is damaged or is missing.

This is a fairly simple fix that can be completed by any competent DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a fresh layer can be applied. It is crucial to keep in mind that when it comes to uPVC window repairs, do not be tempted to apply too much caulk in order to make the area harder to clean and could decrease the efficiency of your energy usage.

Check that any drainage holes are free of debris in them, and also ensure that the sill pan has been properly angled to drain away from the window. In more severe cases, you may need to replace the window.

Mold spots and rotted sills are another sign of water leakage. This is a fungus that thrives in damp conditions and can quickly spread throughout the house.

It is also important to note that if the leak is coming from between the glass in your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open with a breeze, it may be hinges that are at fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like any mechanical component hinges will wear out over time. Changing a window hinge is an easy process, but it's easier if you have someone to help you hold the frame in place.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. Look for the arrows on each hinge to determine which direction the window repair near me should be opened.

The problem can be caused either by opening the window incorrectly or due to a poor installation in the factory. This issue can be fixed by sending us a picture on our website. We will be pleased to offer you suggestions.

It is also essential to ensure that the hinges are lubricated on a regular basis. Applying a light engineering lubricant to the hinges is a great way to do this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. It is recommended to do this at least once a year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges can also become unbalanced due to wear, which can cause a gap where the sash meets frame. They can be repaired by giving them a thorough clean, however when they're beyond repair, it might be necessary to have them realigned or Window Repairs replaced. The interlock may be misaligned. It is located on the hinge side and may need to be cleaned. In some instances it is possible to replace the hinges.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help control indoor temperatures, and window Repairs reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler that can be put on top of your window sill. They will help stop cold air from entering and keep your home warm and cosy!

Your windows made of upvc will continue to provide excellent insulation and security for your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows eventually become worn out, and it may be more cost-effective to replace them instead of fixing them. So, if you're experiencing problems with your upvc windows, it is best to seek professional assistance as soon as possible.