Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it may be time to replace the battery. However, if you replace the battery and it doesn't work it is probably elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have the tools and components required for this service.

Dead Coin Battery

The most frequent reason that your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob comes with an in-built battery which will quickly drain in the event that it is not frequently used. If your remote has started to show signs of a loss in range or stopped working in the middle of the night, then your battery may be dead.

Metal clips hold the battery in inside the key fob. If the clips aren't tight enough, it could lead to contact issues that will stop the remote from receiving power. Utilizing a small screwdriver, push the retaining clip open to remove the current battery and replace it with a new one. Use a battery that has the same voltage, size, and specifications as the original.

Water exposure can cause the key fob to become corroded or damaged. Even a short shower in soapy water can harm the electronic chip within. It's best to keep your key fob in a dry location.

Water Damage

Damage to your water supply could be the cause of your key fob's inability to function properly. The rubber seals on key fobs prevent them from being damaged by a tiny splash or drizzle of water. However, it's important to keep the keys from the ocean, washing machine, and the pool.

The key fob comes with an electronic chip which sends an electronic message to the immobilizer system in your car. This is what allows your 500 to start or lock, however if the chip gets wet, it can no longer work.

You can clean the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to see whether they're still working. However, it is probably recommended to purchase a replacement key for fiat ducato van from a dealership rather than trying to repair the key fob that was submerged in salt water.

A replacement fob can cost you a little bit but it's far less expensive than paying to have your Fiat 500 towed to a dealership and repaired there! You could also do it yourself with some simple steps. Make sure you have the correct type of battery before you attempt to open your key fob. This is a job that's far simpler than it appears and you can find step-by-step instructions online for almost any key fob for your car.

Faulty Chip

The chip that is contained in the key fob communicates with the car's immobiliser unit to make sure your car is only able to start when the correct key is inserted. If the chip is damaged, or damaged in any way the car won't start.

A faulty chip can occur due to many reasons, but the most common reason is water damage or a dead battery. It is best to hand over the work to a professional locksmith who can repair the chip in a short time and at a an affordable cost.

If your key fob does not function after being exposed to clean water from a tap or rain take the battery off. Wipe down the electronic component using a paper towel. If the key fob still isn't working it's likely to be a fried chip and will require replacement.

A few people turn to their dealer when they are in need of an entirely new Fiat key fob, however it can be a expensive alternative. If you are seeking a cost-effective method to have your Fiat key fob repaired, look no further than United Locksmith. We have all the tools and knowledge required to fix your Fiat fob quickly and professionally. manner.

Faulty Receiver Module

Fiat 500X Key Fob key fobs send an electrical signal to the vehicle that can unlock and close doors (and start the car if it has an automatic transmission) up to 50 feet. However there are a few factors that could cause the fob to stop functioning. This can be caused by a dead coin-battery or water damage, worn out buttons as well as a receiver issue. signal interference, or [Redirect-302] an issue with the chip.

If the fob is in a pocket which has been subject to extreme trauma, such as falling on hard floor or being washed in a washing machine and it isn't able to communicate with the car's Body Control Module (BCM). This is because the BCM is a secure system that can only accept signals from a genuine original key and not accept any other.

If this is the case, you will require replacing your fob. A professional locksmith will handle the entire process of replacing keys including programming a brand new key for your 500. They can even provide you with the fob cloned to work exactly like the original (and costs one-third of the cost).