Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. In contrast to aluminium and timber, they are not susceptible to corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home, and could even be fatal. It is essential to make sure that your windows are in good working order.

Single-pane windows are fairly simple to replace and will usually fit into the frames that were previously in use very easily. If you have double glazed window repairs near me-paned windows that are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this case you'll need locate some plastic spacers that will help the new pane to fit perfectly into the frame of the window.

If you are going to try to remove the glass panes yourself it is important to wear the proper safety gear, including thick gloves and eye protection. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not onto the floor which could cause them to be trampled.

It's a great idea seal the gap after the glass has been removed. This will keep drafts and water from entering your home until a professional is able to repair the window. It also acts as a barrier to prevent any intruders from getting into your home. If the gap is particularly large, you might want to consider using an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows with sash. However, upvc window repair over time, they are susceptible to a range of problems including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. It's important to take action as soon as you notice your uPVC windows are falling down.

Repositioning the hinges can aid in fixing a window that is sagging. You'll first need to open the windows so you can get at the frame. Then, remove both the hinges on the top and bottom with a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, close the window and verify the fit. If you're satisfied with the fit of your window, you can tighten screws to hold them in the right position.

If you are unable to move the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity with time, causing them to loose their elasticity. If this happens, it's essential to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and draught-proof.

uPVC handles may also loosen up. Often, this is caused by screws that have become loose over time. However, it can be due to the fact that the handle mechanism has been worn out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. First, you'll need to close the window and then perform a test to ensure that it fits. The joints at the corners of the sash should align with the joint on the casing. If it doesn't then you can make use of a screwdriver to loosen the handle, and then turn the mechanism back into its original position.

3. Water Leaks

It is important to act if you wake up every morning to find a smoky wall and floors that are wet. Water leaks through windows can cause structural damage to your home, and impact your ability to regulate the temperature inside your home. The most common cause for leaks in uPVC windows is that the sealant surrounding the frame is damaged or missing.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on how severe the issue is, the old caulking may need to be removed. It is crucial to keep in mind that when it comes to upvc Window repair window repairs, do not be tempted to apply too much caulk' as this will only make the area more difficult to clean and can reduce the efficiency of your energy.

Make sure that the drainage holes do not have debris in them and ensure that the sill pan has been angled correctly to drain away from the window. In more serious cases you might have to consider replacing the window.

Mold spots and rotten sills are other signs of water leakage. This mold thrives in damp environments and can quickly spread throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely that the issue is with the seal than the frame. It is also possible to be repaired by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open in a breeze, it may be hinges that are at the fault. They can be easily replaced by any competent DIYer and can be done within a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that are hinged and, just like any mechanical component they are susceptible to wear and tear over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier to do if you have someone to help you hold the frame in place.

It is also important to ensure that the uPVC hinges are being opened and closed in the right direction. You can do this by looking for the arrow on each hinge. This indicates the direction in which the window should open.

The issue could be caused either due to opening the window in the wrong way or by a poor installation at the factory. Sending us a photo via our website is often enough to solve the issue. We are always happy to provide suggestions.

Regularly lubricating hinges is also essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication will make the window easier to open and close. It can also lower the chance of windows getting stuck and stop corrosion. It is recommended to do this once a year. WD40 and other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by a variety of different factors. The hinges can also be disaligned as a result of wear, causing gaps between the frame and sash. This can be easily repaired by giving them a good cleaning, but in the event that they are beyond repair it might be necessary to get them aligned or replaced. Secondly the interlock, this is located on the hinge of the window, can be misaligned. Again, it's feasible to give them a good clean, but in certain cases, it may be necessary to have them replaced.

The seals may wear out or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures and lessen the possibility of draughts.

Lastly, one of the most effective ways to cut down on draughts is by using a draught excluder, these are typically fabric tubes that are filled with some sort of filler and can be positioned on the windowsill on top. They can keep your home warm by blocking cold air.

With a bit of regular maintenance and repairs your windows made of upvc will provide excellent insulation and security for your home. It is crucial to recognize that all windows have a lifespan and eventually, they will reach an point at which it is more economical to replace them than fix them. If you encounter any issues with your window made of upvc, it's best to consult an expert as soon as you can.