Fiat 500 Replacement Key Fob

It's possible to change the battery if your 500 remote key fob is not working. If you do replace the battery and it continues to stop working the issue is likely to be elsewhere.

United Locksmith specializes in the production of new keys for classic vehicles. We have all the necessary tools and parts to perform this service.

Dead Coin Battery

The most common reason why your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob comes with a coin cell battery that is prone to draining quickly when it isn't being utilized frequently enough. If your remote is beginning to show signs like a loss of range or has stopped working and the battery is not working, it could be dead.

Metal clips keep the battery securely inside the key fob. If the clips aren't tight enough, they could cause problems with contact, which can prevent the remote from receiving power. Make use of a flathead screwdriver to pry open the retaining clip and then remove the old battery. Be sure to use a replacement battery with the same type of voltage, size, and specification as the original battery.

Water exposure can also cause the key fob to corrode or be damaged. Even a short bath in soapy water may harm the electronic chip within. It is recommended to keep your key fob in a dry environment.

Water Damage

Damage to your water supply could be the reason for your key fob not functioning properly. The rubber seals on key fobs prevent them from getting damaged by a small drizzle or splash of water. However, it's crucial to keep your keys from the ocean, washing machine, and even the pool.

The key fob has an electronic chip which sends an electronic message to the immobilizer system in your car. This is the reason why your 500 can start or lock, however in the event that the chip becomes wet, Fiat Key Fobs it can no longer work.

You can try cleaning the inside electronics of your keyfob using isopropyl alcohol or an electronic cleaner to see whether they're still in good condition. It is recommended to replace a key fob in the event that it has been submerged into salt water rather than try to repair it yourself.

While a replacement fob might cost a little money, it is far less expensive than having to pay for your fiat 500 key fob not working 500 to be towed to the dealer for repair! You can also do it yourself with just a few steps. Make sure you have the correct battery type before you attempt to open your key fob. There are step-by-step directions for any car keyfob on the internet.

Faulty Chip

The chip in the key fob communicates directly with the immobiliser on your car to ensure that your vehicle will only start when the proper keys are inserted. If the chip is damaged or damaged in any way it will not start.

Damage to the water or a dead cell phone battery are the most common reasons for a faulty chip. It is best to leave the task to a professional locksmith, who can repair the chip quickly and at a reasonable price.

If your key fob fails to function after exposure to clean water from the tap or rain, unplug the battery and clean the electronic component with a paper towel to ensure it is fully dry before putting it back into. If the key fob will not work, there is an opportunity that it is an issue with the component and requires to be replaced.

Many people will seek out their dealer when in need of a new Fiat key fob, but this can be a very costly option. United Locksmith is the best place to go if you need your Fiat keyfob fixed at a reasonable price. We have the equipment and know-how to fix your fiat 500 key cover fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle that can unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. However, there are some things that could cause the fob to stop functioning. This could be due to a dead coin battery damaged by water or worn buttons as well as a receiver module problem and signal interference, or a malfunctioning electronic chip.

If the fob was located in the pocket that has been subject to severe trauma (such as being dropped onto a hard floor or being washed in a washing machine) the fob may not be in a position to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that will only accept a signal from a genuine key and not any other.

You'll have to replace the fob if this occurs. A professional locksmith can handle all aspects of the key replacement process and even program a new one for the 500. In fact, they can offer you a clone key that functions the same as your original fob (and costs less than the price).